Airmar Switchboxes—SB264, SB260 Bedienungsanleitung PDF herunterladen

WARNING: Always wear safety goggles and a dust

mask when installing to prevent personal injury.

WARNING: The power must be “OFF” before

proceeding with the installation.

WARNING: A safe installation requires a 0.5 amp fast-

blow fuse or circuit breaker. Failure to do so may

damage the product and/or result in fire, damage to

the boat, and/or personal injury.

CAUTION: To reduce electrical interference from

other electrical wiring and any on-board equipment with

strong magnetic fields such as radar equipment, radio

transmitters, boat engines, generators, etc., separate

the cables by at least 1m (3').

CAUTION: Be careful not to tear the cable jackets

when passing them through bulkheads and other

parts of the boat. Use grommets to prevent chaffing.

Use deck glands to prevent water seepage into the

boat.

CAUTION: Use a multimeter to check the polarity and

the connections to the 10 - 32 VDC power supply

before applying power to the transducer(s).

IMPORTANT: Please read the instructions completely

before proceeding with the installation. These

instructions supersede any other instructions in your

instrument manual if they differ.

17-498-01 rev.02 12/14/10

Switchbox with Remote Switch

Models: SB260, SB264

Applications

• Single transmission line transducers and echosounders only

• 1kW echosounders only. Do not use with 2 kW echosounders.

• SB260 switches between:

- Two depth transducers connected to one echosounder. The

transducers must use C32 or C332 cable.

- Two echosounders connected to one depth transducer. The

echosounder must be dual-frequency with a single

transmission-line. The transducer must use C32 or C332

cable.

• SB264

Switches between a wide-beam and a narrow-beam depth

transducer connected to one echosounder. Pair a wide-beam

SS264W with one of the narrow-beam models such as: B258,

B260, or M260. Both transducers must have C32 or C332

cable.

Tools & Materials

Safety glasses

Dust mask

Grommets (some installations)

Deck glands (some installations)

Cutting pliers

Phillips screwdrivers

Pencil

Electric drill

Drill bits:

Switchbox 3mm or 1/8"

Remote switch 11mm or 1/2" spade bit

Sandpaper

Weak solvent (such as alcohol)

Wire strippers

Heat shrink tubing

Blade screwdriver

Pliers

Adjustable wrench

Cable ties (some installations)

Locating Switchbox, Remote Switch & Cables

IMPORTANT: Be sure to allow an extra 25 cm (10") of cable to

make the connections within the switchbox.

Switchbox—Select a convenient dry mounting location for the

water-resistant switchbox about 1–2m (3' – 5') from the echo-

sounder(s).

• Retrofit—If the transducer(s) and echosounder(s) are already

installed, select a location with easy access to the cable(s). Be

sure the cable(s) will be long enough to make the necessary

connections. Allow an extra 25 cm (10") for wiring ease.

• New installation—Install the transducer(s) and echosounder(s)

before connecting the switchbox. Plan the cable runs.

Remote Switch—Locate the remote switch on the dash panel or

other convenient location near the echosounder. Check the back-

side for any obstructions such as cables and wires.

• Minimum clearance on backside 36mm (1-1/2")

• Maximum panel thickness6mm (1/4”)

INSTALLATION INSTRUCTIONSOWNER’S GUIDE &

Figure 1. SB264 Switchbox and remote switch

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Switchbox with Remote Switch

WARNING: Always wear safety goggles and a dust mask when installing to prevent personal injury.WARNING: The power must be “OFF” before proceeding with

Seite 2 - Preparing the Cables

Running the CablesIf new equipment is being installed, route the transducer cable(s), the echosounder cable(s), the power cable, and the remote switch

Seite 3 - Connecting the Switchbox

Connecting the SwitchboxCAUTION: Be sure to connect each wire to the correct terminal in the correct terminal block.Wire each cable to its correspondi

Seite 4 - Completing the Installation

Verwandte Modelle: Switchboxes—SB260

Kommentare zu diesen Handbüchern

Keine Kommentare

Airmar Switchboxes—SB264, SB260 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Airmar Switchboxes—SB264, SB260 herunter. Airmar Switchboxes—SB264, SB260 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: Switchboxes—SB260

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Airmar Switchboxes—SB264, SB260