Airmar S61—Transom Mount Bedienungsanleitung PDF herunterladen

17-032-01 rev. 02 04/12/11

Transom Mount

Speed & Temperature Sensor

Models: S61, S63

Applications

• Not recommended for boats with large inboard engine(s).

• Designed for operation from 1–50kn (1–58MPH).

• Fits transom angles from 13–20

° (most powerboats and small

fiberglass and aluminum boats).

For all other transom angles (including 3° transoms on jet boats

and vessels with stepped or undercut transoms) a tapered

plastic, wood, or metal shim must be fabricated.

• S63 can be snapped onto a P37, P52 or P55 transducer.

Tools & Materials

Safety goggles

Dust mask

Scissors

Masking tape

Electric drill

Drill bit, hole saw or spade bit for:

Bracket holes 4mm, #23 or 9/64"

Fiberglass hull only chamfer bit (preferred), 6mm or 1/4"

Transom hole (optional) 20mm or 13/16"

Cable clamp holes 3mm or 1/8"

Marine sealant (suitable for below waterline)

Screwdrivers

Putty knife

Pencil

Zip-ties

Water-based antifouling paint (mandatory in salt water)

Pretest

Connect the sensor to the instrument and spin the paddlewheel.

Check for a speed reading and the approximate air temperature. If

there is no reading(s) or it is inaccurate, check the connections

and repeat the test. If there is still no reading(s) or it is inaccurate,

return the product to your place of purchase.

Mounting Location

CAUTION: Do not mount in an area of turbulence or bubbles:

near water intake or discharge openings; behind strakes, struts,

fittings, or hull irregularities

CAUTION: Avoid mounting the sensor where the boat may be

supported during trailering, launching, hauling, or storage.

• For the best performance, the sensor must be in contact with

smooth water. To identify an area of clean water, observe the

water flow off the transom while the boat is underway.

• Mount the sensor as close to the centerline (keel) of the boat as

possible to ensure the sensor remains in the water when the

boat is turning.

• Single drive boat—Mount at least 75mm (3") beyond the

swing radius of the propeller (see Figure 1). The starboard side

where the propeller blades are moving downward is preferred.

• Twin drive boat—Mount the sensor between the drives.

• Stepped transom—Mount the sensor on the step.

S61 with S63 with

Align the

template’s fold

line with the hull

bottom and fold

under the hull

Figure 1. Mounting location on single drive boat

75mm (3")

min. beyond

swing radius of

propeller

bracket bracket

Follow the precautions below for optimal product

performance and to reduce the risk of property

damage, personal injury, and/or death.

WARNING: Always wear safety goggles and a dust

mask when installing

WARNING: When the boat is placed in the water,

immediately check for leaks around the screws and

any other holes drilled in the hull.

CAUTION: Never pull, carry, or hold the sensor by the

cable as this may sever internal connections.

CAUTION: Never strike the sensor.

CAUTION: Never use solvents. Cleaners, fuel, paint,

sealants, and other products may contain strong

solvents, such as acetone, which attack many plastics

greatly reducing their strength.

IMPORTANT: Please read the instructions completely

before proceeding with the installation. These

instructions supersede any other instructions in your

instrument manual if they differ.

INSTALLATION INSTRUCTIONSOWNER’S GUIDE &

Record the information found on the cable tag for future reference.

Part No._________________Date___________

1 2 3 4

Inhaltsverzeichnis

Seite 1 - Transom Mount

17-032-01 rev. 02 04/12/11Transom MountSpeed & Temperature SensorModels: S61, S63Applications• Not recommended for boats with large inboard engine

Seite 2 - Installation

2InstallationMounting Directly to the HullCAUTION: Do not position the leading edge of the sensor lower than the trailing edge because aeration will o

Seite 3 - Testing on the Water

3Cable RoutingCAUTION: Do not remove the connector to ease cable routing. If the cable must be cut and spliced, use Airmar’s splash-proof Junction Box

Seite 4 - Antifouling Paint

4Obtain parts from your instrument manufacturer or marine dealer.Gemeco Tel: 803-693-0777(USA) Fax: 803-693-0477email: [email protected] EMEA Tel