Airmar Analog to NMEA 0183 Speed & Temperature Data C Bedienungsanleitung PDF herunterladen

17-444-01 rev. 03 12/14/10

Analog to NMEA 0183 Format

Data Converter

for Speed and/or Temperature Data

Parts

Gemeco Tel: 803-693-0777

(USA) Fax: 803-693-0477

email: [email protected]

Airmar EMEA Tel: +33.(0)2.23.52.06.48

(Europe, Middle East, Africa) Fax: +33.(0)2.23.52.06.49

email: [email protected]

Figure 1. Connecting (not to scale) (CS4500 installation shown)

Application

To convert analog speed and temperature data to NMEA 0183

digital format.

Guidelines

CAUTION: To reduce electrical interference from other electrical

wiring and any on-board equipment with strong magnetic fields such

as radar equipment, radio transmitters, boat engines, generators,

etc., separate the cables by at least 1m (3').

CAUTION: Be careful not to tear the cable jackets when passing

them through the bulkhead(s) and other parts of the boat. Use

grommet(s) to prevent chafing.

CAUTION: Make power connections to a 12 VDC power source

that is isolated from the engine start battery(s). Voltage drops may

cause the instrument/receiver/sensor to lose information and/or

change operating mode.

CAUTION: Use a multimeter to check the polarity and the con-

nections to the power supply before applying power to the sensor.

Tools & Materials

Safety goggles

Dust mask

Pencil

Grommet(s) (some installations)

Cutting pliers

Phillips screwdrivers

speed & temperature

sensor

power

12 VDC

Data Converter

display

sensor/instrument cableData Converter cable

Black 12 VDC –

Red 12 VDC +

White NMEA A/+

Blue NMEA B/–

Bare Shield

Wire Function

Color

terminal

block

temp

5V out

ground

signal in

temp

brown

red

bare

green

white

bushing

terminal function

wire color

INSTALLATION INSTRUCTIONSOWNER’S GUIDE &

WARNING: Always wear safety goggles and a dust

mask when installing to avoid personal injury.

WARNING: The power must be OFF before wiring if

the instrument is already connected to a power source

to avoid personal injury or death.

WARNING: The power supply voltage must be

12 VDC. Any other voltage may damage the sensor

and/or result in fire, causing damage to the boat,

personal injury, and/or death.

WARNING: A safe installation requires a 0.5 amp fast-

blow fuse or circuit breaker. Failure to do so may result

in fire, causing damage to the boat, personal injury,

and/or death.

IMPORTANT: Read the instructions completely

before proceeding with the installation. These

instructions supersede any other instructions in your

instrument manual if they differ.

Alcohol (optional)

Wire strippers

Heat-shrink tubing

Heat gun

Blade screwdrivers

Electric drill

Drill bit 3mm or 1/8"

1 2

Inhaltsverzeichnis

Seite 1 - Analog to NMEA 0183 Format

17-444-01 rev. 03 12/14/10Analog to NMEA 0183 Format Data Converterfor Speed and/or Temperature DataPartsGemeco Tel: 803-693-0777(US

Seite 2 - Completing the Installation

Kommentare zu diesen Handbüchern

Keine Kommentare

Airmar Analog to NMEA 0183 Speed & Temperature Data C Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Airmar Analog to NMEA 0183 Speed & Temperature Data C herunter. Airmar Analog to NMEA 0183 Speed & Temperature Data Converter User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Airmar Analog to NMEA 0183 Speed & Temperature Data C