Airmar H2183—Heading Sensor Bedienungsanleitung Seite 1
Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Airmar H2183—Heading Sensor herunter. Airmar H2183—Heading Sensor User Manual Benutzerhandbuch
- Seite / 16
- Inhaltsverzeichnis
- LESEZEICHEN
- Heading Sensor 1
- Introduction 4
- Features 4
- Tools & Materials 6
- Where to Purchase Parts 6
- Installing 8
- Preparing the Sensor 9
- Connector on Display End 12
- RS422 RS232 13
- Connecting to an NMEA 2000 14
- Network 14
- Calibrating the Compass 15
- Trademarks 16
- Maintenance 16
- Troubleshooting 16
- Firmware Revisions 16
Inhaltsverzeichnis
1Record the serial number found on the underside of the sensor.Serial No.____________ Date of Purchase______________17-472-01 rev.05 05/21/14
10Attaching the Sensor to the Bracket1. Feed the cable through the mounting bracket (see Figure 3).2. Align the word ‘FORWARD’ pointing forward and pa
11Flush Mounting on a Horizontal Surface1. Remove the label from over the sensor’s socket (part A) (see Figure 4).2. Apply removable thread locker to
12Cable Routing & ConnectingDepending on the equipment you will be using, route the sensor cable to an Airmar Converter or Combiner, an NMEA 0183
13No Connector on Display End: WiringIf your sensor cable does not have a connector on the display end, it must be hard wired. Referring to the owner’
14Connecting to an NMEA 2000® NetworkCAUTION: Only two termination resistors are required on an NMEA 2000 network. More than two will degrade the bus
15Calibrating the CompassWARNING: The internal compass may need to be calibrated after the sensor is installed for maximum accuracy. Perform the prete
16MaintenanceCAUTION: Do not disassemble the sensor. There are no user-serviceable parts inside. Removing the screws from the sensor (part A) will dam
2All Rights Reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded, or
3Table of ContentsIntroduction... 4Safety Instructions...
4IntroductionThank you for purchasing an Airmar solid-state sensor. The compact housing is waterproof with a single removable cable. The H2183 is actu
5Follow the safety precautions below to reduce the risk of poor product performance, property damage, personal injury, and/or death.WARNING: Correct I
6Cables & Connecting/Converting HardwareThe Heading Sensor can be connected in several ways. You must have the correct cable and any needed hardwa
7Choosing the Mounting LocationFor accurate readings, selecting the best location for the sensor is very important. It can be mounted on either a vert
8InstallingCAUTION: The word ‘FORWARD’ on the sensor must be facing forward and parallel to the centerline of the vehicle/boat for accurate compass re
9Preparing the SensorWARNING: Do not use the studs if there is any danger that a person may be injured by the protruding metal.1. Remove the label fro
Weitere Dokumente für Sensoren Airmar H2183—Heading Sensor
Verwandte Produkte und Handbücher für Sensoren Airmar H2183—Heading Sensor
(4 Seiten)
(4 Seiten)
(4 Seiten)
(4 Seiten)
(4 Seiten)
(4 Seiten)
(2 Seiten)
(4 Seiten)
(6 Seiten)
(4 Seiten)
(6 Seiten)
(4 Seiten)
Denso BHT-200QW podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Czytniki kodów kreskowych Denso BHT-200QW.
Dostarczamy 5 pdf podręczników Denso BHT-200QW do pobrania za darmo według typów dokumentów: Dokumentacja, Instrukcja Użytkownika
Kommentare zu diesen Handbüchern