Airmar CM422—Welded-Tank Mount Bedienungsanleitung PDF herunterladen

17-589-01 rev. 02 03/24/14

Applications

• Keel mount in fiberglass hull only.

• Keel mount recommended for high-speed boats.

Hole Saw

Hole Saw 95mm or 3-3/4”

Mounting Location

CAUTION: Do not mount in line with or near water intake or

discharge openings or behind strakes, fittings, or hull irregularities

that will disturb the water flow.

Choose a Location

• In a cool well-ventilated area away from the engine to avoid

overheating.

• Where the transducer will be in contact with the water at all

times.

• Where the water flowing under the hull is smoothest with a

minimum of bubbles and turbulence (especially at high speeds).

Do not mount the transducer near water intake or discharge

openings; or behind strakes, fittings, or hull irregularities.

• Where the transducer beam will not be blocked by the propeller

shaft(s).

• Away from interference caused by power and radiation sources

such as: the propeller(s) and shaft(s), other machinery, other

echosounders, and other cables. The lower the noise level, the

higher the echosounder gain setting that can be used.

• Where there is working space inside the vessel.

WARNING: The transducer must be professionally

installed using accepted practices. The pocket must be

strong and watertight to reduce the risk of property

damage, personal injury, and/or death.

INSTALLATION INSTRUCTIONSOWNER’ S GUIDE &

Keel Mount

Depth Transducer

Model: CM422

US Patent 7,369,458. UK 2 414 077

Record the information found on the cable tag for future reference.

Part No._________________Date___________Frequency________kHz

Follow the safety precautions below for optimal

product performance and to reduce the risk of

property damage, personal injury, and/or death.

WARNING: Always wear safety goggles and a dust

mask when installing.

WARNING: Immediately check for leaks when the

boat is placed in the water. Do not leave the boat

unchecked for more than three hours. Even a small

leak may allow considerable water to accumulate.

CAUTION: Do not install in the engine compartment or

other hot place. The transducer may fail if it overheats.

CAUTION: Always operate the transducer in water.

Operating in air will allow the transducer to overheat

resulting in failure.

CAUTION: Orient the transducer so the bosses on the

top are facing fore and aft—parallel to the centerline of

the boat.

CAUTION: The transducer must be flush with the

bottom of the hull for good performance.

CAUTION: Never pull, carry, or hold the transducer by

the cable. This may sever internal connections.

CAUTION: Never strike the transducer.

CAUTION: Never use solvents. Cleaners, fuel, sealants,

paint, and other products may contain solvents that can

damage plastic parts, especially the transducer’s face.

IMPORTANT: Please read the instructions completely

before proceeding with the installation. These

instructions supersede any other instructions in your

instrument manual if they differ.

1 2

Inhaltsverzeichnis

Seite 1 - Depth Transducer

17-589-01 rev. 02 03/24/14Applications• Keel mount in fiberglass hull only.• Keel mount recommended for high-speed boats.Hole SawHole Saw 95mm or 3-3/

Seite 2 - Checking for Leaks

Kommentare zu diesen Handbüchern

Keine Kommentare

Airmar CM422—Welded-Tank Mount Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Airmar CM422—Welded-Tank Mount herunter. Airmar CM422—Welded-Tank Mount User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Airmar CM422—Welded-Tank Mount